Skip to Content

Condition Description

UL94 V-0 is the flame requirement most often written on drawings for electrical and electronic structural parts. Flame-retardant grades achieve it with additives, at the cost of lower toughness, reduced chemical resistance, higher price and, for some additive systems, less stable long-term electrical properties.

This page lists the materials and stock shapes rated V-0 in our catalogue. The decision order should be: first confirm the end-product certification actually requires V-0; then check whether the part sits near a heat source or a high-voltage circuit; only then compare strength, temperature rating and cost among the qualifying candidates.

Candidate Materials for This Condition

12 products matchedAll mandatory criteria met
See excluded products (30) and reasons
  • PA66尼龙66板|高强度耐热|齿轮轴套通用工程塑料Flame rating HB below required V-0
  • PA66尼龙66棒|Ø6–200mm|高强度耐磨|传动件用Flame rating HB below required V-0
  • PA66尼龙板|90MPa高强度 低吸水0.6%|精密传动绝缘件Flame rating HB below required V-0
  • PA66尼龙棒|90MPa高强度|精密轴套/齿轮加工用Flame rating HB below required V-0
  • PA6尼龙板|耐磨自润滑 抗蠕变|机械结构件通用Flame rating HB below required V-0
  • PA6尼龙棒|Ø6–200mm|耐磨抗蠕变|轴套导轨用Flame rating HB below required V-0
  • PBT板|低吸水0.1% 尺寸稳定|轴承连接器绝缘件Flame rating HB below required V-0
  • PBT棒|高尺寸稳定性|精密机械与电气绝缘件Flame rating HB below required V-0
  • PC/ABS合金板|高抗冲300J/M|手板模型与设备外壳Flame rating HB below required V-0
  • PC/ABS合金棒|低温抗冲|机械零件与外壳加工Flame rating HB below required V-0
  • PETP板(PET-P)|高刚度低蠕变|食品级绝缘件Flame rating HB below required V-0
  • PETP棒|耐磨低摩擦|替代进口Ertalyte型材Flame rating HB below required V-0
  • POM棒(赛钢)|Ø6–200mm|精密传动件加工用Flame rating HB below required V-0
  • PPO板(改性聚苯醚)|低介电2.65 耐热137℃|电气绝缘Flame rating HB below required V-0
  • PPO棒|低介电高刚性|高频绝缘与化工件加工Flame rating HB below required V-0
  • PPSU板|可反复蒸汽灭菌|医疗器械与消毒盒用Flame rating V-2 below required V-0
  • PPSU棒|耐160℃ 高抗冲|医疗与耐热结构件Flame rating V-2 below required V-0
  • PSU聚砜板|琥珀透明 耐热177℃|替代Udel P-1700Flame rating V-2 below required V-0
  • PSU聚砜棒|耐160℃ 高抗冲|耐热绝缘结构件Flame rating V-2 below required V-0
  • UPE500超高分子量聚乙烯板|500万分子量 耐磨抗冲Flame rating HB below required V-0
  • UPE500超高分子量聚乙烯棒|500万分子量|耐磨衬套Flame rating HB below required V-0
  • UPE980超高分子量聚乙烯板|980万分子量 极致耐磨Flame rating HB below required V-0
  • UPE980超高分子量聚乙烯棒|980万分子量|高耐磨件Flame rating HB below required V-0
  • 加纤PA尼龙板(GF30)|140MPa高刚性|叶轮阀体齿轮Flame rating HB below required V-0
  • 加纤PA尼龙棒(GF30)|140MPa|高承载传动件Flame rating HB below required V-0
  • 加纤PBT板(GF30)|HDT200℃ 高刚性|汽车连接器Flame rating HB below required V-0
  • 加纤PBT棒(GF30)|150MPa 耐热150℃|精密结构件Flame rating HB below required V-0
  • 导电PA尼龙板|10³–10⁵Ω全断面导电|半导体载具Flame rating HB below required V-0
  • 导电PA尼龙棒|10³–10⁵Ω|防静电工装与传动件Flame rating HB below required V-0
  • 导电POM工程塑料棒Flame rating HB below required V-0

Your selection criteria: Flame rating V-0

or contact us directly

32 products match this condition. To filter by your specific parameters, use the Full Material Selector →

Basis for Judgment and Key Points

FAQ

What is the difference between V-0, V-1 and V-2?

All three require self-extinguishing after removal of the flame. They differ in afterflame time and whether dripping ignites cotton: V-0 has the shortest afterflame and no igniting drips, V-1 is slightly looser, and V-2 permits igniting drips. Strictness decreases in that order.

Flame-retardant PC or flame-retardant PPS?

Choose FR PC for cost-sensitive structural and cosmetic parts; choose PPS where chemical resistance, high temperature or greater dimensional stability is needed. PPS is inherently flame retardant, usually without added flame retardants, so long-term electrical performance is more stable.

What does the thickness range on the yellow card mean?

UL rates flame performance by thickness. The same grade may reach V-0 at 0.8 mm and only HB at 3 mm. For thin-wall parts, verify the rating at your actual thickness rather than relying on the grade name.

Smart Material Selection