Skip to Content

Condition Description

Precision fits (IT7 and tighter) in engineering plastics rarely fail because of insufficient strength; they fail because dimensions drift with ambient humidity. PA nylon is the usual culprit: equilibrium moisture absorption is typically 1.5 to 2.5 percent, producing dimensional change of 0.3 to 0.6 percent - enough to consume the entire fit tolerance.

This page ranks candidates by dimensional stability, creep resistance and strength. POM absorbs about 0.2 percent moisture, has good stiffness and machines stably, making it the default for precision parts; PEEK balances temperature resistance and dimensional stability at higher cost; PC is dimensionally stable and tough, but only average in chemical and wear resistance.

Candidate Materials for This Condition

12 products matchedAll mandatory criteria met
See excluded products (17) and reasons
  • PC/ABS合金板|高抗冲300J/M|手板模型与设备外壳Tensile strength 59 below required 60 MPa
  • PC/ABS合金棒|低温抗冲|机械零件与外壳加工Tensile strength 59 below required 60 MPa
  • PPO板(改性聚苯醚)|低介电2.65 耐热137℃|电气绝缘Tensile strength 58 below required 60 MPa
  • PPO棒|低介电高刚性|高频绝缘与化工件加工Tensile strength 58 below required 60 MPa
  • PPS聚苯硫醚板|HDT250℃ 耐酸碱|变压器骨架泵阀Tensile strength 40 below required 60 MPa
  • PPS聚苯硫醚棒|耐220℃ 耐化学|泵阀与绝缘件Tensile strength 40 below required 60 MPa
  • PTFE聚四氟乙烯板(铁氟龙)|耐260℃ 全耐化学Tensile strength 18 below required 60 MPa
  • PTFE聚四氟乙烯棒(铁氟龙)|自润滑绝缘|密封件用Tensile strength 18 below required 60 MPa
  • PTFE车削板(铁氟龙膜板)|0.5–3mm薄板|密封垫片用Tensile strength 18 below required 60 MPa
  • 导电PA尼龙板|10³–10⁵Ω全断面导电|半导体载具Tensile strength 55 below required 60 MPa
  • 导电PA尼龙棒|10³–10⁵Ω|防静电工装与传动件Tensile strength 55 below required 60 MPa
  • 钢氟龙PVDF聚偏氟乙烯板|耐150℃ 高纯低析出|超纯水管路Tensile strength 50 below required 60 MPa
  • 钢氟龙PVDF聚偏氟乙烯棒|耐化学 可焊接|泵阀与管路件Tensile strength 50 below required 60 MPa
  • 防静电PPS板|10⁶–10⁹Ω 耐220℃|电子载具齿轮Tensile strength 40 below required 60 MPa
  • 防静电PPS棒|10⁶–10⁹Ω 耐高温|电子工装与传动件Tensile strength 40 below required 60 MPa
  • 阻燃PC板|UL94 V-0 抗冲700J/M|电源外壳绝缘件Tensile strength 57 below required 60 MPa
  • 阻燃PC棒|V-0阻燃 高抗冲|电气绝缘结构件Tensile strength 57 below required 60 MPa

Your selection criteria: Tensile strength ≥ 60 MPa

or contact us directly

56 products match this condition. To filter by your specific parameters, use the Full Material Selector →

Basis for Judgment and Key Points

FAQ

Does moisture conditioning make PA dimensions stable?

Conditioning brings parts close to the moisture equilibrium of the service environment quickly and reduces further growth, but it does not remove the effect of humidity fluctuation itself. Where humidity varies widely, tolerance the part for the wettest condition.

POM or PEEK for precision parts?

Choose POM for ambient temperature, ordinary media and cost sensitivity; choose PEEK where high temperature, chemical resistance or longer life is required. POM machines well and holds dimensions, which is why it is the most common precision-part material.

How tight a tolerance is possible in plastic?

It depends on material, wall thickness and process. Machined POM and PEEK commonly reach plus or minus 0.05 mm, tighter with special design; injection moulded parts are governed by shrinkage and tooling, so tolerances follow the material shrinkage. Moisture-absorbing materials should be dimensioned in the conditioned state.

Smart Material Selection